Cost-effective 18 port full managed Gigabit Layer-2 switch +2x SFP MiniGbic slots without fan for desktop and 19" rack installation.
ALLNET Switch full managed 16 Port Gigabit 280W / 16x PoE+ / 2x SFP / Fanless / 19" / "ALL-SG8618PM"
Highlights:- 16 port Gigabit Layer2+ switch architecture
- Supports NWay protocol for speed (10/100/1000Mbps) and duplex mode (half/full) auto-detection
- Supports back-pressure (half duplex), flow control (IEEE 802.3x and IEEE 802.3az Energy Efficient Ethernet)
- VLAN 4K Static / Port-Based / Tagged Based / Protocol / Voice VLAN / 802.1ad Q-in-Q
- Link Aggregation static link / LACP / Algorithm MAC based or IP based
- IGMP Snooping 256 groups IGMP v1/v2/v3, Fast Leave
- QoS (QoS>QoS multi-label, queue config, QoS mapping)
- Stormcontrol
- Total fanless, no more annoying noise... max. 280W budget
- 19 "inch angle or wall/table mounting possible
The new ALLNET ALL-SG8618PM switch is an optimal basis for small and medium workgroups with high network and data traffic and enables fast data transmission in the network. With a total of 16 downward compatible Gigabit PoE ports, the connected PoE end devices are reliably and powerfully interconnected.
Due to the fanless design, the ALL-SG8618PM is also ideal for use in office environments, as no disturbing noise is generated. The switch is Layer 2+ fully managed and supports all necessary standards like QoS, VLAN, Spanning Tree, IGMP Snooping up to Link Layer Discovery Protocol. This ensures highest performance & security in your network.
The robust metal housing is suitable for mounting in a 19" cabinet as well as for wall mounting. The ALL-SG8618PM also has 2x SFP miniGBIC slots to connect remote server/uplink end devices via fiber optic cable.
Rich PoE Management Function
Being the managed PoE switches for CCTV surveillance, wireless and VoIP networks, ALL-SG8626PM features the following special PoE management functions: - PoE PD-alive check
- Scheduled power rebooting
- PoE schedule
- PoE usage monitoring
- Soft-reboot PoE Non-stop
- PoE port power feeding priority
Smart PoE PD-Alive Check
ALL-SG8618PM managed PoE switch can be configured to monitor connected PD status in real time. Once the PD stops working and responding, ALL-SG8618PM will resume the PoE port power and bring the PD back to work. They will greatly enhance the network reliability through the PoE port resetting the PD?s power source and reducing administrator management burden.
PoE Schedule Function for Energy Saving
For environmental protection purpose, the ALL-SG8618PM switch Ethernet PoE can effectively control the power supply besides its capability of giving high watts power. The PoE schedule function helps to enable or disable PoE power feeding for each PoE port during specified time intervals and it is a powerful function to help SMBs or enterprises save power and money.
Scheduled PD Re-starting
The ALL-SG8618PM smart switch PoE allows each of the connected PoE IP cameras or PoE wireless access points to reboot at a specific time each week. Therefore, it will reduce the chance of IP camera or AP crash resulting from buffer overflow.
1588 Time Protocol for Industrial Computing Networks
The ALL-SG8618PM is ideal for telecom and Carrier Ethernet applications, supporting MEF service delivery and timing over packet solutions for IEEE 1588 and synchronous Ethernet.
Strong Layer 2 Features
The ALL-SG8618PM layer 2 Ethernet switch can be programmed for advanced Layer 2 switch management functions such as dynamic port link aggregation, 802.1Q tagged VLAN, Q-in-Q VLAN, private VLAN, Multiple Spanning Tree Protocol (MSTP), QoS, bandwidth control, IGMP snooping and MLD snooping. Via the aggregation of supporting ports, the ALL-SG8618PM allows the operation of a high-speed trunk group that comes with multiple ports and supports fail-over as well.
Efficient and Various Management Methods
For efficient management, the ALL-SG8618PMis equipped with console, Web and SNMP management interfaces.
With the built-in Web-based management interface, it offers an easy-to-use, platform-independent management and configuration facility.
For text-based management, it can be accessed via Telnet and the console port.
For standard-based monitor and management software, it offers SNMPv3 connection which encrypts the packet content at each session for secure remote management.
Intelligent PoE Switch SFP DDM Function
The AALL-SG8618PM supports SFP-DDM (digital diagnostic monitor) function that greatly helps network administrator to easily monitor real-time parameters of the SFP transceivers, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.
Technical Data:
Model
|
ALL-SG8618PM
|
Copper Ports
|
16-10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
|
Fiber Ports
|
2-100/1000BASE-X SFP interfaces, supports 100/1000Mbps dual mode
|
PoE Ports
|
1~16-802.3af/802.3at PoE Injector Ports
|
Console Ports
|
1 x RS-232-to-RJ45 serial port (115200, 8, N, 1)
|
Switch Architecture
|
Store-and-Forward
|
Switch Fabric
|
36 Gbps/non-blocking
|
Throughput
|
26.78 Mpps @64 bytes
|
Address Table
|
8K entries
|
Share Data Buffer
|
4 Mb
|
Jumbo Frame
|
9600 Bytes
|
SDRAM
|
1Gb
|
Flash Memory
|
128Mb
|
Flow Control
|
IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
|
Reset Button
|
>2 sec.: Factory default and reset
|
Power Supply
|
100~240V AC, 50/60Hz, 4A (max.)
|
Power Consumption
|
Max. 280 watts/1122 BTU
|
PoE Standards
|
IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/PSE
|
PoE Power Supply Type
|
Per Port 52V DC, 300mA. Max. 15.4 watts (IEEE 802.3af)
Per Port 52V DC, 600mA. Max. 30 watts (IEEE 802.3at)
|
LED Indicators
|
Power: Green
Solid on- power work normal, off- power disconnected
System: Green
Blink -work normally, solid on- soft work abnormal, fast Blink ? soft upgrade
PoE: Yellow
Solid on- PoE work normally, Off- PoE doesn?t work, Blink - PoE overload
10/100/1000T RJ45 Interfaces (Port 1 to Port 16): 1000 LNK/ACT (Green) Blink - port connected with data transmission; Solid on- port connected without data transmission
100/1000Mbps SFP Interfaces (Port 17 to Port 18): Green
Blink - port connected with data transmission; Solid on- port connected without data transmission
|
EMC
|
Surge Immunity:
4KV Per: IEC61000-4-5
ESD Protection:
ESD Level 4 Per: IEC61000-4-2
EFT Level 4 Per: IEC61000-4-4
|
Layer2 Functions |
Port configuration
|
Auto-negotiation Flow Control
Port Mirror: TX/RX/BOTH; Many-to-1 monitor
CPU Mirror
Traffic statistics
|
Link Aggregation
|
Static link aggregation
LACP (Dynamic Trunk/Static Trunk)
Algorith based on Source/Destination MAC
Algorithm based on Source/Destination IP
|
MAC Table
|
Aging Time
Static MAC address
Dynamic MAC address management
|
VLAN
|
4094 Active VLANs
4094 VID
802.1Q Tag VLAN
Port VLAN
Protocol VLAN
MAC VLAN
Voice VLAN
802.1ad Q-in-Q tunneling
Private VLAN (Protected port)
GARP/GVRP
|
ACL
|
256ACLs
L2, L3 e L4
Time-based ACL
IP ACL
MAC ACL
MAC-IP ACL
User-Defined ACL
ICMPv6
|
Spanning tree
|
802.1D Spanning Tree Protocol (STP)
802.1w Rapid Spanning Tree Protocol (RSTP)
802.1s Multiple Spanning Tree Protocol (MSTP)
Loop Guard
Root Guard
TC-BPDU Guard
BPDU Guard
BPDU Filter
|
Ring Protection |
<20ms G.8032 ERPS Ring
Fast Ring
|
Multicast |
256 groups
IGMP v1/v2/v3 Snooping, Fast Leave
MLD Snooping
Multicast VLAN
IGMP filter
MVR
Multicast Routing
|
QOS
|
8 mapping IDs to 8 level priority queues
CoS port-based
CoS 802.1p-based
CoS DSCP-based
Scheduling algorithms SP, WRR, SP+WRR
Storm Control (Broadcast, Multicast, Unknown Unicast)
Bandwidth control per port
SWRR, DWRR for Scheduling
Flow Redirect
Precedence
TOS
Rate Limiting (Ingress/Egress)
Stri Priority
|
Security Features
|
Port Security
MAC address filter
ARP Association (Manual, ARP scanning, DHCP snooping)
ARP Protection
AAA
DAI
DoS (Denial of Service)
Classification of packages based on: End.MAC, IP End, TCP / UDP Ports, Protocol Type;
802.1x Authentication (port-based e MAC-based)
TACACS/TACACS+ Authentication
RADIUS Authentication
DHCP Filter
Guest VLAN
SSLv2/SSLv3/TLSv1
SSHv1/SSHv2
Restriction of WEB access based on: IP Address, And. MAC and Port;
Port Isolation
Loopback detection
|
Management
|
SNMP v1/v2c/v3 with Full Private MIBs
RMON 4 groups
WEB (HTTP/HTTPS)
CLI (Telnet, Console, SSHv1/v2)
Firmware upgrade via console/web/TFTP
Configuration Backup/Reload
Dual Firmware
LLDP
Configuration Export/Import
CDP Aware
OAM (IEEE802.3ah)
CFM (IEEE802.1ag)
sFlow
|
Synchronization, IEEE1588
|
Support IEEE1588v2 transparent clock
|
Other Features
|
DNS Client
DHCP Relay
DHCP Client
DHCP Snooping
DHCP Option 66
DHCP Option 67
DHCP Option 82
NTP/SNTP Client
UPNP
UDLD
|
PoE management
|
Total PoE power budget control
Per port PoE function enable/disable
PoE admin-mode control
PoE port power feeding priority
Per PoE port power limitation
PD classification detection
PD alive check
PoE schedule
Soft-reboot PoE Non-stop
|
Maintenance
|
Cable Diagnostics
Ping
SFP DDM (Digital Diagnostics Monitoring)
Thermal protection
System log (Local and Remote)
Memory and CPU Monitoring
|
Layer 3 functions |
Static Routing
|
IPv4 Unicast: Static Routing(Software Base)
IPv6 Unicast: Static Routing(Software Base)
|
IPV6
|
IPv6 neighbor discovery (ND)
Path maximum transmission unit (MTU) discovery
Internet Control Message Protocol (ICMP) version 6
TCPv6/UDPv6
Ping6
Telnet(v6)
Http/Https
Interface IPV6
ACL IPV6
|
Dimension
|
440x290x44.5mm
|
Weight
|
4 kg
|
Working Temperature
|
-10°C to 45°C
|
Storage Temperature
|
-20°C to 70°C
|
MTBF
|
50,000hrs
|
|
| | Patchkabel RJ45 FTP(F/UTP) 0.25m grau, CAT5e, Synergy 21, | | | Patchkabel RJ45 FTP(F/UTP) 0.5m grau, CAT5e, Synergy 21, | | | Patchkabel RJ45 FTP(F/UTP) 1.0m grau, CAT5e, Synergy 21, | | | Patchkabel RJ45 FTP(F/UTP) 2m grau, CAT5e, Synergy 21, | | | Patchkabel RJ45 FTP(F/UTP) 3m grau, CAT5e, Synergy 21, | | | Patchkabel RJ45 FTP(F/UTP) 5m grau, CAT5e, Synergy 21, | | | Patchkabel RJ45 FTP(F/UTP) 7.5m grau, CAT5e, Synergy 21, | | | Patchkabel RJ45 FTP(F/UTP) 10m grau, CAT5e, Synergy 21, | | | Patchkabel RJ45, 0.25m grau, CAT5e, S-FTP(SF/UTP), Synergy | | | Patchkabel RJ45, 0.5m grau, CAT5e, S-FTP(SF/UTP), Synergy 2 | | | Patchkabel RJ45, 1.0m grau, CAT5e, S-FTP(SF/UTP), Synergy 2 | | | Patchkabel RJ45, 2m grau, CAT5e, S-FTP(SF/UTP), Synergy 21, | | | Patchkabel RJ45, 3m grau, CAT5e, S-FTP(SF/UTP), Synergy 21, | | | Patchkabel RJ45, 5m grau, CAT5e, S-FTP(SF/UTP), Synergy 21, | | | Patchkabel RJ45, 7.5m grau, CAT5e, S-FTP(SF/UTP), Synergy 2 | | | Patchkabel RJ45, 10m grau, CAT5e, S-FTP(SF/UTP), Synergy 21, | | | Patchkabel RJ45, 15m grau, CAT5e, S-FTP(SF/UTP), Synergy 21, | | | Patchkabel RJ45, CAT6 250Mhz, 0.25m grau, S-STP(S/FTP), LSZH, Synergy 21, | | | Patchkabel RJ45, CAT6 250Mhz, 0.5m grau, S-STP(S/FTP), LSZH, Synergy 21, | | | Patchkabel RJ45, CAT6 250Mhz, 1.0m grau, S-STP(S/FTP), LSZH, Synergy 21, | | | Patchkabel RJ45, CAT6 250Mhz, 2m grau, S-STP(S/FTP), LSZH, Synergy 21, | | | Patchkabel RJ45, CAT6 250Mhz, 3m grau, S-STP(S/FTP), LSZH, Synergy 21, | | | Patchkabel RJ45, CAT6 250Mhz, 5m grau, S-STP(S/FTP), LSZH, Synergy 21, | | | Patchkabel RJ45, CAT6 250Mhz, 7.5m grau, S-STP(S/FTP), LSZH, Synergy 21, | | | Patchkabel RJ45, CAT6 250Mhz,10m grau, S-STP(S/FTP), LSZH, Synergy 21, | | | Patchkabel RJ45, CAT6 250Mhz,15m grau, S-STP(S/FTP), LSZH, Synergy 21, | | | TP(RJ45) POE-Tester, at/af, Endspan/Midspan, standard, Synergy 21, |
Downloads Back |