Highlights:- 60 Watts, selectable Mode A and Mode B
- Industrial Gigabit POE Injector with voltage booster
- accept 24 VDC to boost up voltage to 55V for 60Watts application
- 1x10/100/1000M TX PSE (802.3af/at POE+) TX
- 1x10/100/1000M TX
- Operating temp: -40°C to +75°C
Introduction
This Super Voltage Booster --- 60 Watts, high power Single port industrial POE Injector is equipped with our high efficiency ColdDesign technology which allows low input voltage, such as 24/48/56 VDC be boost up to 55VDC to provide 60Watts to 72 Watts power to your security equipment by a 4-pin selectable dip switch. The ColdDesign technology will not only boost up Input Voltage, also reduce the excessive heat problem to a minimum. It accepts the input voltage as low as 24/48 VDC to boost up to 55V to meet IEEE802.3af/at required voltage. This built-in 4 pin dip switches are able to select POE for Mode B or Mode A, to select standard IEEE802.3at 30Watts or high power 36Watts, and to select 2 pair or 4 pair for 30/36Watts or 60/72Watts power output. It is being rigorously tested for your Security, Transportation and Telco application.
Technical Details:
IEEE Standard
|
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE802.3af for POE
IEEE802.3at for POE+
|
Network Connector :
|
1xRJ-45 10/100/1000BaseT(X) Data
1xRJ-45 10/100/1000BaseT(X) PSE with POE Output power
|
Network Cable
|
UTP/STP Cat.5e or above Cable
|
EIA/TIA-568 10-ohm (100m)
|
Protocol
|
CSMA/CD
|
LED
|
PW1(power 1) Green: ON- power good, OFF-power failed
PW2(power 2) Green: ON- power good, OFF-power failed
Mode A : ON- End Span PD detected
Mode B: ON ? Mid Span PD detected
4 Pair: ON ? 60W PSE in active mode.
OFF ? 30W PSE in active mode.
|
POE Pin Assignment
|
Default: Mode A (End Span) V+, V+, V-, V- for pin 1, 2, 3, 6
DIP switch setting can be changed to Mode B, V+, V+, V-, V- for pin 4, 5, 7, 8
|
DIP Switch
|
To select 2 pair (30/36Watts) or 4 pair (60/72Watts)
To select Mode A, or Mode B
To select standard IEEE802.3at 30watts or high power POE 36Watts
|
Reverse polarity protection
|
Present
|
Overload current protection
|
Present
|
Power Supply
|
2 Redundant power source
24V-56V VDC Power Input,
|
Power Consumption
|
1 W@24/48 VDC full load, Without POE
|
POE power
|
Maximum POE power 72watts at 24/48VDC input
|
Removable Terminal Block
|
Provide 4 pin terminal block
Wire range: 0.34mm^2 to 2.5mm^2
Solid wire (AWG):12-24/14-22
Stranded wire(AWG): 12-24/14-22
Torque:5lb-In/0.5Nm/0.56Nm
Wire Strip length: 7-8mm
|
Operating Temperature
|
-40° ~ 75° fully tested.
|
Operating Humidity
|
5% to 95% (Non-condensing)
|
Storage Temperature
|
-40°~85°
|
MTBF (mean time between failure)
|
510,304 hrs ( MIL-HDBK-217F) at 25°C
|
Housing
|
Rugged Metal, IP30 Protection
|
Case Dimension (L X W X D)mm
|
103.5mmx32mmx81.5mm (LxWxD)
|
Installation mounting
|
DIN Rail mounting and Wall Mounting
|
Certifications:
|
EN55022/24
|
ITE equipment
|
EN55011
|
Industrial, Scientific and Medical (ISM) equipment
|
Safety
|
IEC EN60950-1
|
EMC/EMS
|
CE, FCC, VCCI
|
EMI
|
FCC Part 15 Subpart B Class A,
CE EN 55022 Class A
|
EN 50155 / EN 60068-2-6
|
Vibration
|
EN 50155 / EN 60068-2-27
|
Shock
|
EN 50155 / EN 60068-2-32
|
Free Fall
|
|
 | | Synergy 21 Netzteil - 48V 75W Mean Well Hutschiene, schmal |  | | Synergy 21 Netzteil - 48V 240W Mean Well Hutschiene |  | | Mean Well Netzteil - 48V 120W Hutschiene, schmal |  | | Synergy 21 Netzteil - 48V 480W Mean Well Hutschiene |  | | ALLNET 19"zbh. Gerätehalter für Hutschiene/DIN-Rail Geräte, T150mm/5HE, Lichtgrau, Frontmontage, |  | | ALLNET DIN-RAIL Wandgehäuse, T223mm, Lichtgrau, IP55, SO-DIN-Serie, |  | | ALLNET 19"Wandgehäuse, 9HE, T488mm, Lichtgrau, IP55, SO-Serie, incl. 2-Fach Lüftereinheit |
Downloads Back |